Русская версия

Search document title:
Content search 2 (exact):
ENGLISH DOCS FOR THIS DATE- Meter Trim Check (replaced) - B660727 | Сравнить

SCANS FOR THIS DATE- 660727 - HCO Bulletin - Meter Trim Check [B006-015]
CONTENTS METER TRIM CHECK Cохранить документ себе Скачать
REPLACED
see HCO B 11 May 1969
Volume VI-369
REPLACED
see HCO B 11 May 1969
Volume VI-369
HUBBARD COMMUNICATIONS OFFICE
Saint Hill Manor, East Grinstead, Sussex
HCO BULLETIN OF 27 JULY 1966
HUBBARD COMMUNICATIONS OFFICE
Saint Hill Manor, East Grinstead, Sussex
HCO BULLETIN OF 27 JULY 1966
RemimeoRemimeo
All OrgsAll Orgs
Tech SecTech Sec
Qual SecQual Sec
All Tech HatsAll Tech Hats
All Qual HatsAll Qual Hats
(Tech Div)
(Qual Div)
(Tech Div)
(Qual Div)

METER TRIM CHECK

METER TRIM CHECK

E-Meters can go out of trim during a session because of temperature changes.

E-Meters can go out of trim during a session because of temperature changes.

Thus even if the meter is properly calibrated and reads at 2.0 with a 5,000 ohm resistor across the leads and 3.0 with 12,500 ohms, by the end of the session a pc can be apparently reading below 2.0 because the meter is off trim.

Thus even if the meter is properly calibrated and reads at 2.0 with a 5,000 ohm resistor across the leads and 3.0 with 12,500 ohms, by the end of the session a pc can be apparently reading below 2.0 because the meter is off trim.

Low TA cases are not cracked by lower level auditing, and have to be handled with Power Processing. Erroneously calling a pc a “low TA case” could thus deny him lower level processes that he could win on.

Low TA cases are not cracked by lower level auditing, and have to be handled with Power Processing. Erroneously calling a pc a “low TA case” could thus deny him lower level processes that he could win on.

The following meter procedure is therefore to be followed AT THE END OF EACH SESSION (AFTER GIVING “THAT’S IT”):

The following meter procedure is therefore to be followed AT THE END OF EACH SESSION (AFTER GIVING “THAT’S IT”):

1. DON’T MOVE THE TRIM KNOB

1. DON’T MOVE THE TRIM KNOB

2. PULL OUT THE JACK PLUG

2. PULL OUT THE JACK PLUG

3. MOVE THE TA UNTIL THE NEEDLE IS ON “SET” AT THE SENSITIVITY YOU WERE USING IN THE SESSION

3. MOVE THE TA UNTIL THE NEEDLE IS ON “SET” AT THE SENSITIVITY YOU WERE USING IN THE SESSION

4. RECORD THE TA POSITION AT THE BOTTOM OF THE AUDITOR’S REPORT FORM AS: “Trim check — TA = . . .”

4. RECORD THE TA POSITION AT THE BOTTOM OF THE AUDITOR’S REPORT FORM AS: “Trim check — TA = . . .”

5. IF YOUR METER IS KNOWN TO BE OUT OF CALIBRATION (as in Para 2 above) RECORD ALSO: “Calibration error — ....... on meter= 2.0 actual” at the bottom of the form.

5. IF YOUR METER IS KNOWN TO BE OUT OF CALIBRATION (as in Para 2 above) RECORD ALSO: “Calibration error — ....... on meter= 2.0 actual” at the bottom of the form.

L. RON HUBBARDL. RON HUBBARD
LRH:lb-r.rdLRH:lb-r.rd

[This HCO B is replaced by HCO B 11 May 1969, Meter Trim Check, page 369.]

[This HCO B is replaced by HCO B 11 May 1969, Meter Trim Check, page 369.]