1 / 2 - Полуправда. “В этой сессии, Вы сказали мне какую-либо полу-правду, неправду, или сказали что то только для того, чтобы произвести впечатление на меня, или пытались навредить кому-либо?” “Что это было?”

? Или К: “В этой сессии, Вы не сумели ответить на какой-либо вопрос или команду?” “На какой вопрос или команду Вы были не в состоянии ответить?”

Решение: “Есть что-либо, что Вы решили на этой сессии?” “Что это было? ”

В/Х: “В этой сессии, Вы подумали, сказали, или сделали что - нибудь, что я не сумел выяснить?” “Что это было?”

The Class II Model Session has the benefit of requiring no other Rudiments process (except in the Havingness Questions) than the question itself. There are, therefore, no additional processes except Havingness.

Од: “На этой сессии, что - нибудь было неправильно понято?” “Что это было ?”

Beware of any Q and A in using this script (HCO Bulletin May 24, 1962 [ l ] ).

Don’t stray off Model Session into unusual questions or processes. Use Model Session as the surround for processes to be run on the pc. Don’t use it as a process.

Questions are asked of the pc and not checked on the needle. Auditor watches meter and records TA.

All auditing sessions have the following preliminaries done in this order.

1. Seat the pc and adjust his or her chair.

2. Clear the Auditing room with “Is it all right to audit in this room?” (not metered).

3. Can squeeze, “Put your hands in your lap.” “Squeeze the cans, please.” And note that pc registers on the meter by the squeeze read on the meter, and note the level of the pc’s havingness. (Don’t run hav here.)

4. Put in R Factor by telling pc briefly what you are going to do in the session. (What you intend to run.)

“Is it all right with you if I begin this session now?”

“START OF SESSION.”

“Has this session started for you?” (If pc says, “No,” say again, “START OF SESSION. Now has this session started for you?”)

GLL: “What goals would you like to set for this session?”

O/W: One would run General O/W if the pc was emotionally upset at the beginning of the session or if the session did not start for the pc, the latter being simply another indication of the pc’s being upset or ARC broken, but these symptoms must be present, as sometimes the session hasn’t started merely because of poor Tone 40 or because the pc had something he wanted to say before the auditor started the session.

“If it is all right with you, I am going to run a short general process. The process is: ‘What have you done?’, ‘What have you not done?’ “ (The process is run very

permissively until the needle looks smooth and the pc is no longer emotionally disturbed. )

“Where are you now on the time track?”

“If it is all right with you, I will continue this process until you are close to present time and then end this process.” (After each command ask, “When?”)

“That was the last command. Is there anything you would care to ask or say before I end this process?”

“End of process.”

Aud: “Are you willing to talk to me about your troubles?” “What trouble aren’t you willing to talk to me about?”

W/h: “Since the last time I audited you, have you done anything you are withholding?” (If pc says, “Yes”) “What was it?”

PTP: “Do you have a present time problem?” “What is the problem?”

“Now I would like to run this process on you (name it). What would you say to that?” (Get pc’s agreement; if not obtainable, choose another process unless old process is not complete.)

“In this session is there anything you have suppressed, not-ised, failed to reveal, or been careful of?” “What was it?”

“If it is all right with you, I will give this command two more times and then end this process.” (Gives command two more times.)

“Is there anything you would care to ask or say before I end this process?”

“End of process.”

“Where are you now on the time track?”

“If it is all right with you, I will continue this process until you are close to present time and then end this process.” (After each command ask, “When?”)

“That was the last command. Is there anything you would care to ask or say before I end this process?”

“End of process.”

1/2-Un T: “In this session, have you told me any half-truth, untruth, or said something only to impress me, or tried to damage anyone?” “What was it?”

? or C: “In this session, have you failed to answer any question or command?” “What question or command did you fail to answer?”

Dec: “In this session, is there anything you have decided?” “What was it?”

W/h: “In this session, have you thought, said, or done anything I have failed to find out?” “What was it?”

Aud: “In this session, has anything been misunderstood?” “What was it?”

“Have you made any of these goals for this session?” “Thank you for making these goals for this session,” or “Thank you for making some of these goals for this session. I’m sorry you didn’t make all of them,” or “I’m sorry you didn’t make these goals for this session.”

“Have you made any gains in this session that you would care to mention?” “Thank you for making these gains for this session,” or “I’m sorry you didn’t make any gains for this session.”

(After adjusting the meter) “Put your hands in your lap. Please squeeze the cans.”

(If the squeeze test was not all right, the Auditor would run the pc’s Havingness process until the can squeeze gives an adequate response.)

“Is there anything you would care to ask or say before I end this session?”

“Is it all right with you if I end this session now?”

“END OF SESSION. Has this session ended for you?” (If pc says, “No,” repeat, “END OF SESSION.” If session still not ended, say, “The session has been ended. “)

Most flagrant errors that can be made:

1. Fumbling with script, not knowing Model Session.

2. Failing to get in the R Factor by telling pc what you are going to do at each new step.

3. Doing only what the pc suggests.

4. Adding unusual questions or remarks or making sudden irrelevant statements.

5. Using parts of Model Session as repetitive processes which deter the completion of auditing cycles already begun.

6. Failure to complete the Auditing Comm Cycle on any part of Model Session.